 |
 |
Latest Release Version
Release 3.1.11 with MHL CTS 1.2 support
Latest 980 Manager GUI Version (External and Embedded)
3.1.12
Latest Firmware Version
3.1.11 Build Number: 9602 09/21/2011
Latest Gateware Version
3.2.4 Build Number: 1 09/16/2011
Latest HDMI Source Compliance Test Script Version
3.1.5
Latest HDMI Sink Compliance Test Script Version
3.1.7
Latest MHL Source Compliance Test Script Version
1.2.0
Latest MHL Sink Compliance Test Script Version
1.2.0
This update to the 980 Generation 3 consists of a new version of the firmware/gateware load for the instrument itself. If the 980 does not contain the previous release of 3.1.2, then you will also need to upgrade the 980 Manager program, both on the PC and the embedded version in the instrument. All updates should be performed at the same time, as the 980 Manager GUIs rely on some new features in the instrument firmware/gateware. Click here for the installation procedure (PDF).
This release provides the following new or improved features:
- Updated MHL Source and Sink/Dongle Compliance Test to support MHL CTS 1.2. TPA-MHL-8R is needed.
This release has the following known issues:
- Vtotal in Video Timing is incorrect in real time mode if the received timing's Vfront is equal to 1.
- HEAC MB Audio Off doesn't turn off MB audio.
This update to the 980 Generation 3 consists of a new version of the firmware/gateware load for the instrument itself. If the 980 does not contain the previous release of 3.1.2, then you will also need to upgrade the 980 Manager program, both on the PC and the embedded version in the instrument. All updates should be performed at the same time, as the 980 Manager GUIs rely on some new features in the instrument firmware/gateware. Click here for the installation procedure (PDF).
This release provides the following new or improved features:
- Updated MHL Source and MHL Sink/Dongle Compliance Tests to support MHL CTS 1.2. TPA-MHL-8R is needed.
This release corrects the following issues:
- Improved handling of DVI signals in capture mode and real time mode.
- Fixed issues with real time analysis of 297MHz formats.
- Fixed invalid sampling size decode in Audio InfoFrame.
- Various fixes in HDMI Source Compliance Test.
- Fixed issues in EDID Compliance Test.
This release has the following known issues:
- Vtotal in Video Timing is incorrect in real time mode if the received timing's Vfront is equal to 1.
- HEAC MB Audio Off doesn't turn off MB audio.
Sample EDID Files
This archive contains two sample EDID files you can use for EDID emulation on the 980 Rx port.
980_225MHz_EDID.xml is the default 980 Gen 2 EDID.
- Supports 3D (Frame Packing in selected formats such as 1080p24, Side-by-Side (Half), and Top-and-Bottom).
- Supports VIC codes 1 through 62.
980_300MHz_EDID.xml is the default 980 Gen 3 EDID.
- Supports 4K x 2K formats.
- Supports 3D (Frame Packing in selected formats such as 1080p24, Side-by-Side (Half), and Top-and-Bottom).
- Supports VIC codes 1 through 64.
1. Download Sample EDID Files archive from here (updated on October 14, 2011).
2. Unzip the files into a new folder in your PC.
3. Turn on 980 and launch 980 External Manager GUI.
4. Connect to a 980 instrument.
5. Click on File -> Import -> EDID -> Ok, then browse to the location of the EDID file you want to import and select the XML file.
6. Click on Edid -> Set 980 RX EDID, then select the EDID you want to apply to the 980 Rx port.
If you check the box next to "Permanently set the 980's EDID?" the default 980 EDID will be replaced with the newly applied EDID, and it will persist through power cycles.
If you don't check the box, you can use the newly applied EDID until you power cycle the 980 or apply another EDID.
If you check the box next to "Issue Hot Plug?" a hot plug from the 980 Rx port will be sent after the new EDID is applied.
If you don't check the box, a hot plug will not be sent after the new EDID is applied.
|
|
 |
