 |
There are no new features for the 882E/881E included in the
Release 2.10.5.
The following anomalies have been corrected in the Release
2.10.5.
- Reworded EDID Compliance Test per HDMI CTS 1.3b. "Too
many preferred" means the same as "Native DTD
count larger than number of DTDs."
- Fixed the problem where the generator hangs when leaving
HdcpProd in certain cases.
- Fixed the problem where VGA analog signal is shifted by
4 pixels.
- Fixed the problem where CEC bit corruption wasn't working.
- Fixed the problem where CEC Rx start error (10303) and
Tx line error (10310) show up when extreme 0 bit low period
is set.
Note: The release files can only be applied
to the 882E/881E generator (not the 882CA/882C/881C, 882D, nor
882EA generators).
The Release 2.10.5 is comprised of the following software components.
| Software Component |
Version |
Change Status |
| Boot Rom |
01.04.11 |
no change |
| vxWorks |
20.1884605 |
new with 2.10.5 |
| Gateware 1 |
404C,1029,7252007 |
new with 2.10.5 |
| Gateware 2 |
401A,8,1082007 |
no change |
| Gateware 3 |
401B,1,8082007 |
new with 2.10.5 |
Java JRE required |
1.5.06 |
no change |
You can upgrade your generator using the procedures in the Users
Guide. Please note that you will have to verify that your
current generator is operating with Release 2.7.0, 2.8.0,
2.8.1, 2.8.2, 2.9.0, or 2.10.2. To verify that your current
generator is operating with one of these releases, enter the
following command:
verf?
Release 2.7.0 should return the following information:
20.1883800, 01.04.11
Release 2.8.0 should return the following information:
20.1884000, 01.04.11
Release 2.8.1 should return the following information:
20.1884200, 01.04.11
Release 2.8.2 should return the following information:
20.1884202, 01.04.11
Release 2.9.0 should return the following information:
20.1884400, 01.04.11
Release 2.10.2 should return the following information:
20.1884602, 01.04.11
After verifying that the generator is operating with Release
2.7.0, 2.8.0, 2.8.1, 2.8.2, 2.9.0, or 2.10.2, upgrade your
generator using the procedures below:
- Download the 2.10.5 Zip file to your PC and unzip the
file. There will be a System and a Library directory.
- Upgrade the generator using the procedures at this link.
- After power cycling the generator, verify that the generator
is running the current 2.10.5 version of the vxWorks file
by entering the following command:
verf?
20.1884605, 01.04.11
- Verify that the vxWorks file is: 20.1884605.
- Verify that the BootRom version is: 01.04.11.
- Verify that the generator is running the current 2.10.5
version of the gateware files by entering the following
command:
verg?
404C,1029,7252007:401A,8,1082007:401B,1,8082007
- The first listing is the Lattice FPGA gateware. The next
two listings are the transmitter gateware files for the
DVI and the HDMI output. The gatewares are separated by
colons. Verify that the transmitter gateware files are:
401A,8,1082007:401B,1,8082007.
You can obtain Release Notes for past releases as follows:
88xE Release 2.10.2
88xE Release 2.9.0
88xE Release 2.8.2
88xE Release 2.8.1
88xE Release 2.8.0
88xE Release 2.7.0
|
|
