Feature Enhancements for 882CA/882C/881C Release 2.13.3 - vxWorks: 20.1885203

There are no new features for the 882CA/882C/881C included in the Release 2.13.3.

The following anomalies have been corrected in the Release 2.13.3.

• Horizontal sync back porch (HSBP) and vertical sync back porch (VSBP) are now calculated correctly.
• Pixel depth (PELD) can now be set by pressing Content -> Options.
• ImageShifting an animated image such as Cubes will no longer hang the front panel and Ethernet connection.
• Changing either the horizontal increment (XISH:HINC) or vertical increment (XISH:VINC) to 0 while ImageShifting will no longer hang the generator.
• Sequence Player will show an asterisk next to ACS when the sync signal type (SSST) is 3 or 4. Previously, the asterisk didn't show up when SSST = 4.
• PacketRx image's Received Other Packets page now shows the correct information. Source number status bits now show up as bits 19-16, and channel number status bits now show up as bits 23-20.
• Selecting an ImageShift file in Browse mode (e.g. /tffs0/Library/Library/ImageShifts/Shift2.xml) to start ImageShifting when the currently selected image is an animated image such as Cubes now works correctly.
• EDID data report and EDID Compliance Test report can now be generated and saved correctly in EDID Editor.
• Only 0 through 30 are valid GPIB addresses that you can configure via front panel.
• PacketRx image's Received Other Packets page no longer shows audio length when the incoming signal is switched to DVI (HDMI-D) from HDMI (HDMI-H).
• "Image not Available" message now tells you what is wrong with the current settings that prevents the image from displaying properly. For example, when you select Pluge in HDMI-H interface, it will say "Must be using analog interface."
• MaxGamut, MaxGamutTV, and NomGamutTV have been reworded to MaxRange, MaxRangeTV, and NomRangeTV respectively. This setting (DVQM) can be found by pressing Source -> Options -> Options in HDMI interface.
• Virtual Display or Virtual Video Display has been renamed to Virtual Front Panel for consistency.
• HDCP Compliance Test's sink tests have been modified to include commands that can set Ainfo and short read configurations. CPTX:WAIN 0 means do not write Ainfo. CPTX:WAIN 1 means write Ainfo. CPTX:CRIP 1 means perform combined read. CPTX:CRIP 0 means perform short read. CPTX:WAIN? and CPTX:CRIP? can be used to query the current configuration. 2C-01 test's S302 can be done now.
• Switching from LipSync image to another image when the moving box is between the lines (when there is no audio) no longer mutes audio in the switched image.
• PNG images are now rendered correctly.
• ImageShifting BMP files in 1080i or 1080p no longer hangs the generator.
• Sink primary aspect ratio test in Test ID 8-17 will no longer be run if you are not running EDID Compliance Test against HDMI CTS 1.3b. It will only be run if you are running EDID Compliance Test against HDMI CTS 1.2a.
• LEVP change in YPbPr no longer changes white color to green color in images such as Philips1.
• Fixed some of HdcpProd image's compliance issues.
• Fixed some issues with ImageShifting BMP files.
• The default image is changed to GenStats.
• Added support for the new main boards.

• Test steps TT01 and TT02 of Test Section 1A-01 are not tested because the application does not have visability into the control bits of the TMDS data islands. Therefore a Pass result on the test report only applies to the tests within that section that are executed.
  
  
• Test steps TT01 and TT02 of Test Section 1B-01 are not tested because the application does not have visability into the control bits of the TMDS data islands. Therefore a Pass result on the test report only applies to the tests within that section that are executed.
  
  
• Test Section 1A-08 is not tested because this test requires a DVD with a list of KSVs that have been revoked. We will support this in the future when the DVD with SRM is available.
  
  
• Test Section 1A-09 cannot be tested because the application cannot collect the TMDS video.
  
  
• Test Section 2C-04 cannot be tested because the application cannot control the positioning of the encryption enable signal in DVI.
  
  

• do not use CMD Terminal tool in the generator's web interface to run the Compliance Test via command line; use Telnet (Ethernet) or HyperTerminal (serial) instead
  
  
• try running the tests in batch mode by using the front panel interface
  
  
• if there is a problem, try running the tests one by one via the command line (see the repeater AB test procedure below as an example and refer to the user guide)
  
  
• running the tests using release 2.6.1 (20.1883610 firmware) saves the test reports in /tffs0/library/reports/
  
  
• running the tests using a release with firmware version 20.1883611 or later saves the test reports in /card0/library/reports if there is a PCMCIA card inserted in the 882CA (/tffs0/library/reports/ if no PCMCIA is inserted)
  
  

• you can monitor the transactions on Tx port 1 using the ACA
  
  

• you can monitor the transactions if you have another 882C/882CA/882E/882EA and a TPA-ACA-3R
  
  
• connect the output of the source device to TPA-ACA-3R's DUT 1, the input 1 of 882CA (test equipment) to TPA-ACA-3R's DUT 2, and output 1 of a different 882C/882CA/882E/882EA (ACA monitoring device) to TPA-ACA-3R's OUT 1
  
  
• use the ACA on the 882C/882CA/882E/882EA that is not the test equipment to monitor the transactions on Tx port 1
  
  

• use a separate source device and connect it to the upstream port of the repeater
  
  
• use the 882CA's Rx 1 port as the sink device and connect it to the downstream port of the repeater
  
  
• you can monitor either downstream or upstream transactions (not both at the same time) if you have another 882C/882CA/882E/882EA and a TPA-ACA-3R
  
  
• in order to monitor the downstream transactions, connect the downstream of the repeater device to TPA-ACA-3R's DUT 1, the input 1 of 882CA (test equipment) to TPA-ACA-3R's DUT 2, and output 1 of a different 882C/882CA/882E/882EA (ACA monitoring device) to TPA-ACA-3R's OUT 1
  
  
• in order to monitor the upstream transactions, connect the output of the source device to TPA-ACA-3R's DUT 1, the upstream of the repeater device to TPA-ACA-3R's DUT 2, and output 1 of a different 882C/882CA/882E/882EA (ACA monitoring device) to TPA-ACA-3R's OUT 1
  
  
• use the ACA on the 882C/882CA/882E/882EA that is not the test equipment to monitor the transactions on Tx port 1
  
  

• connect the 882CA's Tx 1 port to the upstream port of the repeater



• connect the 882CA's Rx 1 port to the downstream port of the repeater



• make sure HdcpProd image is not selected on the 882CA before running the tests



• you can monitor the downstream transactions on Rx port 1 using the ACA



• you can monitor the upstream transactions on Tx port 1 using the ACA

CPTX:DUTT 0 // set up for source test
CPTX:CPTR 16 // configure 2C-1 test
CPTX:CPTU // start the test
// save the test report to the PC and rename it

// repeat above steps for test numbers 17 and 18

CPTX:CPTR 19 // configure 2C-4 test
CPTX:CPTU // start the test
// save the test report to the PC and rename it

CPTX:DUTT 1 // set up for source test
CPTX:CPTR 1 // configure 1A-01 test
CPTX:CPTU // start the test
// save the test report to the PC and rename it

// repeat above steps for test numbers 2 to 14

CPTX:CPTR 15 // configure 1B_06 test
CPTX:CPTU // start the test
// save the test report to the PC and rename it

CPTX:DUTT 3 // set up for repeater AB test
CPTX:CPTR 20 // configure 3A-01 test
CPTX:CPTU // start the test
// save the test report to the PC and rename it

// repeat above steps for test numbers 21 to 28

CPTX:CPTR 29 // configure 3B-05 test
CPTX:CPTU // start the test
// save the test report to the PC and rename it

CPTX:DUTT 2 // set up for repeater C test
CPTX:CPTR 30 // configure 3C1-01 test
CPTX:CPTU // start the test
// save the test report to the PC and rename it

// repeat above steps for test numbers 31 to 44

CPTX:CPTR 45 // configure 3C2-09 test
CPTX:CPTU // start the test
// save the test report to the PC and rename it

The Release 2.13.3 is comprised of the following software components.

You can upgrade your generator using the procedures in the Users Guide. Please note that you will have to verify that your current generator is operating with Release 2.1.x, 2.2.x, 2.3, 2.4, 2.5.x, 2.6.0, 2.8.1, 2.8.2, 2.9.0, 2.10.2, 2.10.4, 2.11.0, 2.12.0, 2.13.1, or 2.13.3. To verify that your current generator is operating with one of these releases, enter the following command:

verf?

Release 2.1.0 should return the following information:

20.1882508, 01.04.11

Release 2.2.0 should return the following information:

20.1882800, 01.04.11

Release 2.2.1 should return the following information:

20.1882901, 01.04.11

Release 2.2.2 should return the following information:

20.1882903, 01.04.11

Release 2.2.3 should return the following information:

20.1882910, 01.04.11

Release 2.3 should return the following information:

20.1883000, 01.04.11

Release 2.4 should return the following information:

20.1883200, 01.04.11

Release 2.5.4 should return the following information:

20.1883404, 01.04.11

Release 2.5.5 should return the following information:

20.1883405, 01.04.11

Release 2.6.0 should return the following information:

20.1883600, 01.04.11

Release 2.8.1 should return the following information:

20.1884200, 01.04.11

Release 2.8.2 should return the following information:

20.1884202, 01.04.11

Release 2.9.0 should return the following information:

20.1884400, 01.04.11

Release 2.10.2 should return the following information:

20.1884602, 01.04.11

Release 2.10.4 should return the following information:

20.1884604, 01.04.11

Release 2.11.0 should return the following information:

20.1884800, 01.04.11

Release 2.12.0 should return the following information:

20.1885000, 01.04.11

Release 2.13.1 should return the following information:

20.1885201, 01.04.11

After verifying that the generator is operating with either Release 2.1.x, 2.2.x, 2.3, 2.4, 2.5.x, 2.6.0, 2.8.1, 2.8.2, 2.9.0, 2.10.2, 2.10.4, 2.11.0, 2.12.0, or 2.13.1 upgrade your generator using the procedures below:

1. Download the 2.13.3 Zip file to your PC and unzip the file. There will be a System and a Library directory.
2. Upgrade the generator using "Upgrading without using PC Card" procedure at this link.
   
3. After power cycling the generator, verify that the generator is running the current 2.13.3 version of the vxWorks file by entering the following command:
   
   verf?
   20.1885203, 01.04.11



4. Verify that the vxWorks file is: 20.1885203.
5. Verify that the BootRom version is: 01.04.11.
6. Verify that the generator is running the current 2.13.3 version of the gateware files by entering the following command:
   
   verg?
   256C,41,5312006:223F,81,9132007:253A,12,9152007



7. The first listing is the CPLD gateware. It might be 253C, 255C, 257C, or 258C. The next two listings are the Tx and Rx gateware respectively. The gatewares are separated by colons. Verify that the Tx gateware file (the second item listed) is: 253F,81,9132007.
8. Verify that the Rx gateware file (the third item listed) is: 253A,12,9152007.

You can obtain Release Notes for past releases as follows:

88xC(A) Release 2.13.1
88xC(A) Release 2.12.0
88xC(A) Release 2.11.0
88xC(A) Release 2.10.4
88xC(A) Release 2.10.2
88xC(A) Release 2.9.0
88xC(A) Release 2.8.2
88xC(A) Release 2.8.1
88xC(A) Release 2.6.0
88xC(A) Release 2.5.5
88xC(A) Release 2.5.4
88xC(A) Release 2.4
88xC(A) Release 2.3
88xC(A) Release 2.2.3