• 3D Testing per HDMI with 3D Bitmap Conversion Tool
• Image Control Tool to fine tune deep color images (882E only).
• DTV ready–Pre-programmed standard DTV formats are ready for immediate use. Digital outputs support YCbCr color encoding. Analog outputs support tri-level composite sync and YPbPr.
• Built-in formats–Over 350 popular video formats are built-in including VESA, ATSC, EIA-770.x, SMPTE 170, 240, 259, 267, 274, 292, 293, 295, 296, Australian, EIA/CEA-861D, NTSC and PAL.
• Central administration–Update and configure all networked instruments from a single computer.
• Network control–Fully control instrument from any network location with web browser or Telnet client.
• Graphics SDK–Create complex patterns based on your specifications using C++ software development kit.
• HDMI–Full single-link HDMI. DVI HDCP production keys for HDMI output.
• Easy to use–Access powerful features easily using intuitive user interface.
• Multiple configurations–Save and restore different instrument configurations for different applications.
• Local pattern storage–Store multiple custom images (.bmp, .jpg, and .png) images in instrument.
• Self-calibrating–Analog video outputs are automatically adjusted against an internal precision reference. This assures video levels that are precise and reliable. Signal levels are auto-adjusted individually.
• Probe–Trigger a scope or inspection camera using the probe signal. Position a pulse anywhere in the frame.
• PC Card–Clone one generator to another using a standard CompactFlash card.
• Auxiliary Channel Analyzer (ACA)–The ACA enables you to monitor DDC, HDCP, CEC and EDID transactions for HDMI and HDCP, Link Layer and EDID transactions over the DisplayPort auxiliary channels.
• IEEE-488-GPIB (IEEE-488) interface. interface.
• RS-232-Industry standard serial interface.

For the 882E one of the two following digital options must be selected:

• HDMI Transmitter:
  • Advanced E-EDID parsing
  • 3D Pattern Testing for HDMI formats
  • Deep Color at 24/30/36-bit/pixel 4:4:4 RGB / YCbCr
  • 16/20/24-bit/pixel 4:2:2 YCbCr
  • High-level Active Format Description (AFD) controls
  • AFD test suite
  • Pixel repetition test suite
  • Automatic and manual InfoFrame setup
  • Compressed Dolby Digital formats (Plus & TrueHD)
  • Internal sine wave generator (LPCM), and external SPDIF audio input
  • 32, 44.1, 48, 88.2, 176.4 and 192kHz audio sampling rates
  • Generates all EIA/CEA-861D formats below 165 MHz, with all possible variations
  • Complete letterbox and scope coverage
  • 4:2:2 color sub-sampling at 8, 10, and 12-bits per component
  • Hot-plug format list
  • Includes DVI-D (M) to HDMI (M) cable and HDMI-HDMI cable.
  
  

• DisplayPort Transmitter:
  • Link layer testing (compliance and monitoring)
  • HDCP compliance testing of sink devices
  • Pixel rates up to 268MHz
  • 1, 2 & 4 lanes user selectable
  • 1.62GB/s and 2.7Gb/s per lane rate user selectable
  • 4:4:4 color sub-sampling
  • 6, 8, and 10-bits per component
  • RGB and YCbCr colorimetry
  • Hot-plug format list
  • Includes DisplayPort cable.
  
  

• Analog Video component and composite (882E HDMI only)
  • Component analog up to 250MHz
  • Component analog VGA Connector
  • Composite analog on S-video and BNC Connectors

For the 882E one of the two following analyzer options can be selected:

• HDMI Analyzer available with HDMI Tx on 882E only
  • Dual HDMI Tx and dual HDMI Rx ports
  • Supports full single-link HDMI (with deep color) and DVI analyzer up to (150MHz) in same instrument.
  • Measure source timing and source pixel errors. Also useful for testing cables. Test results can be issued as formatted reports.
  • Emulate EDIDs.
  
  

• DisplayPort Analyzer available with DisplayPort Tx on 882E only
  • Provides monitoring of auxiliary channel such as EDID, HDCP and link layer transactions through internal connector.
  • Supports link layer compliance testing for DisplayPort source devices in addition to DisplayPort sink devices.
  • Emulate VESA EDIDs.
  • Single DisplayPort Tx and Single DisplayPort Rx ports
  
  

For the 882E HDMI, the following options are available:

• Options with the 882E HDMI
  • CEC Integrated Troubleshooting Environment (ITE)
  
  

• Options with the 882E HDMI Analyzer
  • CEC Integrated Troubleshooting Environment (ITE) - Debug environment
  • CEC Test Management Environment (TME) - HDMI CEC compliance (approved by HDMI)
  • HDCP compliance test - HDMI HDCP CTS 1.2
  
  

For the 882E DisplayPort, the following options are available:

• Options with the 882E DisplayPort
  • VESA EDID 1.4 Verification Test
  
  

• Options with the 882E DisplayPort Analyzer
  • HDCP compliance test for DisplayPort sink devices
  • Link Layer compliance test for DisplayPort sink devices (VESA approved)
  • Link Layer compliance test for DisplayPort sink & source devices (VESA approved)
  • Auxiliary Channel Analzyer (ACA)
  • VESA EDID 1.4 Verification Test
  
  

• Null Modem (p/n 30-00124)–The null modem cable is provide with all 880 series generators. It is used for connecting a PC to the generator to control the generator through the command line interface.
• Ethernet cross over cable (p/n 30-00151)–The Ethernet cross over cable is provide with all 880 series generators. It is used for connecting a PC to the generator for web browser access.
• Line Cord (p/n 30A00400A03)–The 6 foot line cord is provided with all 880 series generators. It is a detachable power cord used to provide power to the generator.
• BNC to RCA adaptor (p/n 30-00123)–The BNC to RCA adaptor is provided with 880 series generators. It is used on the TV to allow a coaxial cable connection from the TV to the generator's BNC TV output.
• DVI to HDMI adaptor (p/n 30-00145)–The 6 foot DVI to HDMI cable is provided with 880 series generators. It is used to connect the generator to a DVI monitor from the generator's HDMI output connector.
• HDMI to HDMI cable (p/n 30-00146)–The 6 foot HDMI to HDMI cable is provided with 880 series generators. It is used to connect the generator to an HDMI monitor from the generator's HDMI output connector.
• DisplayPort to DisplayPort cable (p/n 30-00162)–The 6 foot DisplayPort to DisplayPort cable is provided with 880 series generators. It is used to connect the generator to a DisplayPort monitor or transmitter from one of the 882E DisplayPort connectors.

• ESD-1 (00-00167). Provides external ESD protection for DVI connectors.
• 128MB Compact flash memory card (82-00133 and 82-00134)
• Remote keypad (00-00123) Allow entry of numeric command to load images and formats from up to 43" (1.1 m) from the generator.